I'm Okay!

Hello Friend.

I realize its been almost a year since my last post. And what a time its been. Many life changes have happened between now and then, but maybe most germane is the fact that I moved to another country. This happened late last year, and I've spent most of the intervening time trying to synchronize. In any case, I've had some luck with that and so I hope to pick up where we left off.

So, hello 2018. Its horrendously late, but here it is. I hope everyone has been alright and things are good. With regards to my plans, I actually started penning a short series on practical Encryption last year. I haven't quite finished, but the plan is to put it up as soon as I do. I also intend to expand the scope of the posts here. I won't be doing much hardware work for the nearest foreseeable future, so most of my posts will be more software-centric. I might also occasionally post non-embedded/non-software thingies as well. For example, I discovered that I could install Ubuntu to a USB flash drive and in effect use it as though I had a second hard drive in my laptop. This might be old news, but it was new to me so. Expect a dusting of ML/AI posts as well.

So, I hope to see you again real soon.

Until then.

M.

Comments

Post a Comment

Popular posts from this blog

Getting Started with Logic Analyzers and Pulseview

Image
Hey all, Been a while. Hope you’ve been up to no good, hm? A couple of days ago, I had to do some low-level I2C work on a bare-metal ATMega328P. Digging out the datasheet, I cobbled a simple I2C driver together, the purpose of which was to permit me write a driver for the particular peripheral which would call the lower-level functions the driver provided (i.e things like i2c_start(), i2c_stop(), i2c_address(), etc etc). When I finished the I2C driver, I tested it out with an MMA8452Q I had lying about and it seemed to work just fine. Believing everything to be dandy, I went ahead and wrote the peripheral driver for the component I was working with. And that was when the funny stuff started. To cut that long story short, it wouldn’t work right when deployed to the hardware. At all. I was in a bit of a bind – the code looked great, no errors no nothing, so it was time to look at the hardware/wire-level end of things. Logic analyzers (in my limited understanding) are tools/instrume...
Read more

Bitbanging SPI on the Raspberry Pi (via spi-gpio)

Image
Hello all and happy holidays to everyone! I’m taking a break off work for the holidays so I have a little bit of time on my hands. I will therefore regale you with tales of my exploits! From my last post, I talked about the somewhat “edge” case where you’d want to add (cheap) Ethernet to a Raspberry Pi, probably the A+ or Zero as the case may be. I haven’t figured out the fixed MAC thing just yet, but I’m working on it. Anyways, after some time, another edge-edge case came to me: The ENC28J60 takes up the only SPI peripheral available on the Pi, so what if you needed to use both the ENC28J60 AND some other SPI device? The Pi’s SPI peripheral has two chip selects, so it is theoretically possible to use the exact same bus while using the first chip select for the ENC28J60 (which it uses by default) and using the second chip select for the other device. However, it goes without saying that network communications require some serious computing firepower so it might cause a bit of a perfo...
Read more

Enabling SPI1 on the Raspberry Pi B+/Zero/2/3

Image
Me hearties, Let us plunder and pil.. Sorry, wrong blog. Ahem. Hey all, Its been a while. Been busy at work as usual, and haven’t really had much time to write much. As penance, I will post not one but two updates! This particular post is in relation to Raspberry Pi users specifically. I had earlier talked about the vagaries involved in emulating SPI over GPIO in order to get an additional SPI peripheral. It was a moderately involved process, but the rewards were great With the most recent release of the Raspbian Jessie distribution (2016-05-10), a number of improvements have been made to both the desktop parts and the “under-the-hood” parts, perhaps most significantly the kernel. This new release uses Kernel version 4.4, which now adds the ability to use the second hardware SPI peripheral, SPI1, on the Raspberry Pi. This is only available to devices with the 40-pin header (as seen from the title of this post) so users of the original model A and B will probably need to turn to...
Read more